PRFRM 1 | User manual

SKIN user manual.

Preparation, fitting, controller operation, light modes, charging, technical specifications and important safety information for PRFRM 1 SKIN.

PRFRM 1 SKIN 4 light modes Manual version 1.2

Important safety points

Do not use SKIN if the mask, controller, connector, charging cable or straps are damaged.
Fully charge the controller before first use. SKIN cannot operate while it is charging.
Complete the 10-minute forearm photosensitivity test described below before using SKIN on your face.
Begin every session with clean, dry skin and remove makeup before fitting the mask.
Do not stare directly at the LEDs. Align the eye openings correctly and close your eyes if the light feels uncomfortable.
Stop use immediately if you experience burning, pain, dizziness, persistent redness, swelling or another unexpected reaction.
Keep the mask, controller and charging connection dry. Do not use SKIN in a bath or shower.

Do not use SKIN if you are pregnant or breastfeeding, are photosensitive, take medication that can cause photosensitivity, have a hereditary eye condition, or have a photosensitive skin disorder such as lupus, photosensitive eczema or albinism. If you are unsure whether light exposure is appropriate for you, ask a qualified healthcare professional before use.

SKIN LED mask

The flexible wearable mask containing the LED system.

Controller

Controls power, brightness, light mode and session duration.

Adjustable straps

Secure the mask comfortably during use.

USB charging cable

Charges the controller from a suitable 5V USB power source.

User guide & support

This online manual, PRFRM 1 product support and warranty assistance.

If anything is missing or damaged, do not use SKIN. Contact PRFRM 1 support before continuing.

Prepare your skin

Remove makeup and skincare products, then wash and dry your face completely.

Connect the controller

Align the controller connector correctly and allow it to seat without twisting or forcing it.

Position the mask

Place SKIN over your face and align the eye, nose and mouth openings.

Adjust the straps

Tighten only until the mask feels secure and comfortable. Do not overtighten.

Photosensitivity test

Before first facial use

Place a small section of the illuminated mask against the inside of your forearm and run a 10-minute session.

Check your skin

If you develop redness, itching, swelling, burning or another unexpected reaction, do not use SKIN on your face and seek appropriate medical advice.

Control	Action	Result
Power / Brightness	Press and hold	Switches SKIN on or off.
Power / Brightness	Short press	Cycles through low, medium and high brightness.
Mode / Timer	Short press	Cycles through the four light modes.
Mode / Timer	Press and hold	Selects a 5, 10 or 20-minute session.

Power on

Press and hold the Power / Brightness button. SKIN starts at low brightness.

Set brightness

Short press the Power / Brightness button to move between three levels.

Choose a mode

Short press the Mode / Timer button until the intended mode is selected.

Set the timer

Press and hold the Mode / Timer button to select 5, 10 or 20 minutes.

SKIN switches off automatically when the selected session time ends. To stop earlier, press and hold the Power / Brightness button.

Red — Renew

660nm red and 850nm near-infrared light for routines focused on smoother, firmer and more radiant-looking skin.

Blue — Clarify

450nm blue, 660nm red and 850nm near-infrared light for blemish-prone, congested or unbalanced-looking skin.

Yellow — Calm

590nm yellow and 850nm near-infrared light for routines focused on visible redness, dullness and uneven-looking tone.

Purple — Complete

All four wavelengths combined for comprehensive routines focused on clarity, tone, radiance and visible skin renewal.

Light mode configuration

Mode	Wavelengths	Routine focus
Red — Renew	660nm + 850nm	Smoother, firmer and more radiant-looking skin.
Blue — Clarify	450nm + 660nm + 850nm	Clearer, calmer and more balanced-looking skin.
Yellow — Calm	590nm + 850nm	A calmer, brighter and more even-looking complexion.
Purple — Complete	450nm + 590nm + 660nm + 850nm	Multi-wavelength care for clarity, tone, radiance and visible skin renewal.

Recommended routine

The supplier instructions recommend 3–5 sessions per week over an initial four-week period. Select the mode that best matches your cosmetic skincare focus, choose one of the available 5, 10 or 20-minute session times and begin conservatively.

Do not exceed the recommended frequency merely because SKIN is convenient to use at home. Stop using the device if your skin reacts unexpectedly.

Important: Renew, Clarify, Calm and Complete are routine guidance names, not medical treatment settings. Every mode includes 850nm near-infrared output, which may appear very dim or be invisible to the eye. SKIN is not intended to diagnose, treat, cure or prevent any condition.

Connect

Switch SKIN off, connect the charging cable to the controller, then connect it to a suitable 5V USB source.

Slow flash

A slowly flashing indicator means the controller is charging.

Steady light

A steady indicator means charging is complete.

Rapid flash

A rapidly flashing indicator during normal use means the battery is low and should be recharged.

Disconnect the charging cable before use. Do not charge the controller if the cable, socket or controller is wet or damaged.

Product type	Flexible wearable LED face mask
Selectable modes	Red — Renew, Blue — Clarify, Yellow — Calm and Purple — Complete
Wavelengths	450nm, 590nm, 660nm and 850nm
LED configuration	84 LEDs
LED architecture	Described as 4-in-1 LED technology
Brightness levels	3
Session times	5, 10 or 20 minutes

Dimensions	Approximately 252 × 185 × 139mm
Weight	Approximately 730g
Battery	2000mAh polymer battery
Rated power	7.4W
Rated voltage	3.7V
Charging input	5V, 560mA
Operation while charging	Not supported

Stated LED lifespan	Up to 50,000 hours
Warranty	1 year
Water-resistance rating	Not stated; keep the mask, controller and connections dry

During use

Use SKIN only on clean, dry, intact skin.
Do not stare directly into the LEDs; align the eye openings correctly.
Do not use on broken, inflamed or severely irritated skin.
Check medicines and skincare products for photosensitivity warnings before use.
Keep the controller, connector and mask away from water.
Never use SKIN while it is charging.
Do not cover, modify, dismantle or attempt to repair the device.
Stop if you feel pain, burning, excessive heat, dizziness or another unexpected reaction.

Cleaning and storage

Switch SKIN off and disconnect the controller from charging before cleaning.
Wipe the silicone surface gently with a soft towel or non-abrasive wipe.
Do not immerse the mask or direct water into the controller, connector or charging port.
Do not use abrasive cleaners, solvents, bleach or alcohol unless PRFRM 1 confirms compatibility.
Allow all parts to air-dry completely before the next use or before storage.
Store in a clean, dry place away from direct sunlight, extreme heat and sharp objects.
Do not fold, crush or place heavy objects on the mask.

SKIN will not switch on

Charge the controller fully, disconnect the charging cable, confirm the controller connection, then press and hold the Power / Brightness button.

SKIN will not charge

Check the cable and 5V USB source, reseat both ends and inspect the charging port for moisture, damage or debris.

The indicator flashes rapidly

The battery is low. Switch SKIN off and recharge it before the next session.

The session ends by itself

This is normal when the selected 5, 10 or 20-minute timer reaches zero.

Brightness seems low

SKIN starts at low brightness. Short press the Power / Brightness button to select the next level.

The mode does not change

Use a short press on the Mode / Timer button. Holding the button changes the session time instead.

The timer does not change

Press and hold the Mode / Timer button to cycle between 5, 10 and 20 minutes.

Part of the output looks unlit

Every mode includes 850nm near-infrared output, which may be difficult or impossible to see. Do not stare into the LEDs to check it.

The fit is uncomfortable

Switch off, loosen the straps, realign the openings and refit the mask without overtightening.

Your skin reacts unexpectedly

Stop immediately, remove the mask and do not restart until the reaction has settled and appropriate advice has been obtained.

Unusual heat, smell or damage

Switch off, disconnect SKIN and stop using it. Contact PRFRM 1 support.

PRFRM 1 SKIN is presented as an at-home cosmetic and wellness light device. It is not intended to diagnose, treat, cure or prevent disease. Red, Blue, Yellow and Purple are operational names for the wavelength configurations shown in this manual. Renew, Clarify, Calm and Complete are cosmetic routine guidance names, not medical claims or treatment settings. If you experience an adverse or unexpected reaction, stop use and seek appropriate professional advice.